rad1o

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
= More details about the hardware

== Intro

We want to encourage you to tinker with your rad1o. Write your own software or build a pluggable hardware. Surprise with your creative ideas!

Several people contacted us about producing rad1o for other occasions. All necessary information is on github and we're happy to help. 

=== Schematic

Links: [[https://github.com/rad1o/hardware]]

=== CPU
Name: NXP LPC4330FET180

Description: 32-bit ARM Cortex-M4 microcontroller with Cortex-M0 coprocessor, 264KB (128kB + 72kB + 2x32kB) SRAM, 2x USB 2.0 Device/Host/OTG

Links: [[http://www.nxp.com/products/microcontrollers/product_series/lpc4300/LPC4330FET180.html|Vendor Product Page]] [[http://www.nxp.com/documents/data_sheet/LPC4350_30_20_10.pdf|NXP Datasheet]] [[http://www.nxp.com/documents/user_manual/UM10503.pdf|NXP Manual]] [[http://infocenter.arm.com/help/topic/com.arm.doc.100166_0001_00_en/arm_cortexm4_processor_trm_100166_0001_00_en.pdf|ARM Cortex M4 Technical Reference Manual]]

=== CPLD

Name: XILINX XC2C64A

Description: CoolRunner-II CPLD 64-macrocell Low Power CPLD, 
Links: [[http://www.xilinx.com/support/documentation/data_sheets/ds311.pdf | Datasheet ]]

=== LCD

rad1o comes with a color display:

Name: Nokia 6100

Description: Nokia 6100 - 130x130 LCD

Controller: NXP PCF8833 [[http://lib.chipdip.ru/956/DOC000956837.pdf|Datasheet]] or Epson S1D15G10 [[https://www.sparkfun.com/datasheets/LCD/S1D15G10D08BE_TM_MF1493_03.pdf|Datasheet]]

Connector: Hirose DF23-10DS [[http://www.sparkfun.com/datasheets/LCD/Hirose-DF23.pdf|Datasheet]]



=== RF

HackRF style SDR transceiver, built around the Maxim MAX2837 Wimax Transceiver with an external mixer for up and down converting.

Frequency range from 50 Mhz to 4 GHz (you can maybe operate it up to 6 GHz, but the RF switches and amps are then out of spec).





=== Battery
Description: Custom made 3.7V 1500-2000 mAh rechargeable LiPo battery

=== Dataflash
Name: W25Q16DVSNIG

Description: Serial interface flash memory, 16Mbit of memory organized as 8192 pages of 256 bytes

[[https://www.winbond.com/resource-files/da00-w25q16dv_f2.pdf|Datasheet]] 



=== USB

USB0 Micro USB (2.0) socket (Bootloader can load new Firmware here)
USB1 Micro USB (2.0) socket

=== Audio

4 Pin 3,5mm Headset Connector (Iphone Pinout configured)

^Pin^Name^Description^  
|Tip   |left     | Audio out (bridged mono)|
|Ring1 |right    | Audio out (bridged mono)|
|Ring2 |GND      | Ground|
|Base  |mic      | Audio in (3.3V Bias)|

=== LEDs
^LED ^ Port^ Location ^ Color^
|LD801     |P4_1 |bottom left       |green|
|LD802     |P4_2 |bottom right      |green|
|LD803     |P6_12|left              |green|
|LD804     |PB_6 |top               |red|

=== Misc

One 5 way switch ([[http://www.alps.com/prod/info/E/HTML/MultiControl/Switch/SKRH/SKRHABE010.html|Datasheet]])

== Optional Interfaces
(All not populated)
  
=== X301  External Antenna (SMA)
^Pin^Name^Description^
|Pin  |RF      | RF In/Out|
|Ring |AGND    | Analog Ground| 
 
=== X201  External Clock out (SMA)

^Pin^Name^Description^
|Pin     |CLK3    | Clock Out 3 from Clock Generator|
|Ring    |AGND    | Analog Ground| 

=== JTAG (2x05 male socket (2.54mm/100mil)) 

^Pin^Name^Description^
|1 |VCC    | 3.3V|
|2 |TMS    | Jtag TMS|
|3 |GND    | Ground|
|4 |TCK    | Jtag TCK|
|5 |GND    | Ground|
|6 |TDO    | Jtag TDO|
|7 |nc     | not connected|
|8 |TDI    | Jtag TDI|
|9 |GND    | Ground|
|10|Reset  | Reset ARM|


=== X1    I/O      (2x10 male socket SMD (2.54mm/100mil))

^Pin^Name^Description^  
|1 |nc      | not connected|
|2 |nc      | not connected|
|3 |nc      | not connected|
|4 |nc      | not connected|
|5 |VCC     | 3.3V|
|6 |SD_POW  |  |
|7 |SD_VOLT0| |
|8 |GND     | Ground|
|9 |B2AUX2  | CPLD Bank2-2|
|10|B2AUX1  | CPLD Bank2-1|
|11|B1AUX14 | CPLD Bank1-14|
|12|B1AUX13 | CPLD Bank1-13|
|13|CPLD_TCK| CPLD TCK|
|14|B2F3M2  | CPLD Bank2 F3 M2|
|15|CPLD_TDI| CPLD TDI|
|16|B2F3M6  | CPLD Bank2 F3 M6|
|17|B2F3M21 | CPLD Bank2 F3 M12|
|18|B2F3M4  | CPLD Bank2 F3 M4|
|19|CPLD_TDO| CPLD TDO|
|20|CPLD_TMS| CPLD TMS|
  
 
=== GPIO I/O (2x11 male socket (2.54mm/100mil))

^Pin^Name^Description^  
|1 |VIN      | Input Voltage from USB/Battery|
|2 |RTC_ALARM| Real Time Clock Alarm Out|
|3 |VCC      | 3.3V|
|4 |WAKEUP   | CPU Wake Up|
|5 |GPIO3_8  | CPU GPIO 3-8|
|6 |GPIO3_9  | CPU GPIO 3-9|
|7 |GPIO3_10 | CPU GPIO 3-10|
|8 |GPIO3_11 | CPU GPIO 3-11|
|9 |GPIO3_12 | CPU GPIO 3-12|
|10|GPIO3_13 | CPU GPIO 3-13|
|11|GPIO3_14 | CPU GPIO 3-14|
|12|GPIO3_15 | CPU GPIO 3-15|
|13|GND      | Ground|
|14|ADC1_6   | CDU ADC1-6|
|15|GND      | Ground|
|16|ADC0_2   | CDU ADC0-2|
|17|nc       | not connected|
|18|ADC0_5   | CDU ADC0-5|
|19|GND      | Ground|
|20|ADC0_0   | CDU ADC0-0|
|21|BAT+     | Battery +|
|22|VBAT     | Not Used|
=== CPLD I/O (2x10 male socket (2.54mm/100mil))

^Pin^Name^Description^  
|1 |VCC     | 3.3V|
|2 |GND     | Ground|
|3 |B2AUX16 | CPLD Bank2 AUX16|
|4 |B2AUX15 | CPLD Bank2 AUX15|
|5 |B2AUX14 | CPLD Bank2 AUX14|
|6 |B2AUX13 | CPLD Bank2 AUX13|
|7 |B2AUX12 | CPLD Bank2 AUX12|
|8 |B2AUX11 | CPLD Bank2 AUX11|
|9 |B2AUX10 | CPLD Bank2 AUX10|
|10|B2AUX9  | CPLD Bank2 AUX9|
|11|B2AUX8  | CPLD Bank2 AUX8|
|12|B2AUX7  | CPLD Bank2 AUX7|
|13|B2AUX6  | CPLD Bank2 AUX6|
|14|B2AUX5  | CPLD Bank2 AUX5|
|15|B2AUX4  | CPLD Bank2 AUX4|
|16|B2AUX3  | CPLD Bank2 AUX3|
|17|GCK2    | Clock Generator Out 2|
|18|GCK1    | Clock Generator Out 1|
|19|GCK0    | Clock Generator Out 0|
|20|GND     | Ground|

=== I2SO I/O (2x13 male socket (2.54mm/100mil))

^Pin^Name^Description^  
|1 |CLKIN       | not used|
|2 |CLKOUT      | not used|
|3 |RESET       | CPU Reset|
|4 |GND         | Ground|
|5 |I2C1_SCL    | I2C1 Serial Clock|
|6 |I2C1_SDA    | I2C1 Serial Data|
|7 |SPIFL_MISO  | SPI Flash Master in Slave Out (solder R218 for use)|
|8 |SPIFL_SCK   | SPI Flash Serial Clock (solder R217 for use)|
|9 |SPIFL_MOSI  | SPI Flash Slave In Slave Out (solder R219 for use)|
|10|GND         | Ground|
|11|VCC         | VCC 3.3 V|
|12|I2SO_RX_SCK | I2S RX Serial Clock|
|13|I2SO_RX_SDA | I2S RX Serial DATA Not used|
|14|I2SO_RX_MCLK| I2S RX M Clock|
|15|I2SO_RX_WS  | I2S RX WS|
|16|I2SO_TX_SCK | I2S TX Serial Clock|
|17|I2SO_RX_MCLK| I2S TX M Clock|
|18|GND         | Ground|
|19|U0_RXD      | Uart 0 RX Data|
|20|U0_TXD      | Uart 0 TX Data|
|21|P2_9        | Battery +|
|22|P2_13       | Not Used|
|23|P2_8        | Ground|
|24|I2C0_SDA    | I2C 0 Serial Data|
|25|I2C0_SCL    | I2C 0 Serial Clock|
|26|VDD         | VDD RF 3.3 V Supply|


=== ISP (1x06 male socket (2.54mm/100mil))

^Pin^Name^Description^
|1 |GND    | Ground|
|2 |ISP    | CPU ISP|
|3 |n.c    | Not Connected|
|4 |U0_RXD | Uart 0 RX Data|
|5 |U0_TXD | Uart 0 TX Data|
|6 |RESET  | CPU RESET|




=== Micro SD slot

Optional, not fitted in camp version

Modell: 3M 2908-05WB-MG

[[http://multimedia.3m.com/mws/mediawebserver?66666UuZjcFSLXTtmX&a4x&cEVuQEcuZgVs6EVs6E666666--|Datasheet]]
rad1o

User Tools

Site Tools

Page Tools
