We want to encourage you to tinker with your rad1o. Write your own software or build a pluggable hardware. Surprise with your creative ideas!
Several people contacted us about producing rad1o for other occasions. All necessary information is on github and we're happy to help.
Name: NXP LPC4330FET180
Description: 32-bit ARM Cortex-M4 microcontroller with Cortex-M0 coprocessor, 264KB (128kB + 72kB + 2x32kB) SRAM, 2x USB 2.0 Device/Host/OTG
Links: Vendor Product Page NXP Datasheet NXP Manual ARM Cortex M4 Technical Reference Manual
Name: XILINX XC2C64A
Description: CoolRunner-II CPLD 64-macrocell Low Power CPLD, Links: Datasheet
rad1o comes with a color display:
Name: Nokia 6100
Description: Nokia 6100 - 130×130 LCD
Controller: NXP PCF8833 Datasheet or Epson S1D15G10 Datasheet
Connector: Hirose DF23-10DS Datasheet
HackRF style SDR transceiver, built around the Maxim MAX2837 Wimax Transceiver with an external mixer for up and down converting.
Frequency range from 50 Mhz to 4 GHz (you can maybe operate it up to 6 GHz, but the RF switches and amps are then out of spec).
There are three differnt versions of clock generator ic used SI5351 A / SI5351 B / SI5351 C
Differences on page 18 and following pages.
SI5351 C ⇒ Potentially a clock input can be added
Description: Custom made 3.7V 1500-2000 mAh rechargeable LiPo battery
Name: W25Q16DVSNIG
Description: Serial interface flash memory, 16Mbit of memory organized as 8192 pages of 256 bytes
USB0 Micro USB (2.0) socket (Bootloader can load new Firmware here) USB1 Micro USB (2.0) socket
4 Pin 3,5mm Headset Connector (Iphone Pinout configured)
| Pin | Name | Description |
|---|---|---|
| Tip | left | Audio out (bridged mono) |
| Ring1 | right | Audio out (bridged mono) |
| Ring2 | GND | Ground |
| Base | mic | Audio in (3.3V Bias) |
| LED | Port | Location | Color |
|---|---|---|---|
| LD801 | P4_1 | bottom left | green |
| LD802 | P4_2 | bottom right | green |
| LD803 | P6_12 | left | green |
| LD804 | PB_6 | top | red |
One 5 way switch (Datasheet)
(All not populated)
| Pin | Name | Description |
|---|---|---|
| Pin | RF | RF In/Out |
| Ring | AGND | Analog Ground |
| Pin | Name | Description |
|---|---|---|
| Pin | CLK3 | Clock Out 3 from Clock Generator |
| Ring | AGND | Analog Ground |
| Pin | Name | Description |
|---|---|---|
| 1 | VCC | 3.3V |
| 2 | TMS | Jtag TMS |
| 3 | GND | Ground |
| 4 | TCK | Jtag TCK |
| 5 | GND | Ground |
| 6 | TDO | Jtag TDO |
| 7 | nc | not connected |
| 8 | TDI | Jtag TDI |
| 9 | GND | Ground |
| 10 | Reset | Reset ARM |
| Pin | Name | Description |
|---|---|---|
| 1 | nc | not connected |
| 2 | nc | not connected |
| 3 | nc | not connected |
| 4 | nc | not connected |
| 5 | VCC | 3.3V |
| 6 | SD_POW | |
| 7 | SD_VOLT0 | |
| 8 | GND | Ground |
| 9 | B2AUX2 | CPLD Bank2-2 |
| 10 | B2AUX1 | CPLD Bank2-1 |
| 11 | B1AUX14 | CPLD Bank1-14 |
| 12 | B1AUX13 | CPLD Bank1-13 |
| 13 | CPLD_TCK | CPLD TCK |
| 14 | B2F3M2 | CPLD Bank2 F3 M2 |
| 15 | CPLD_TDI | CPLD TDI |
| 16 | B2F3M6 | CPLD Bank2 F3 M6 |
| 17 | B2F3M21 | CPLD Bank2 F3 M12 |
| 18 | B2F3M4 | CPLD Bank2 F3 M4 |
| 19 | CPLD_TDO | CPLD TDO |
| 20 | CPLD_TMS | CPLD TMS |
| Pin | Name | Description |
|---|---|---|
| 1 | VIN | Input Voltage from USB/Battery |
| 2 | RTC_ALARM | Real Time Clock Alarm Out |
| 3 | VCC | 3.3V |
| 4 | WAKEUP | CPU Wake Up |
| 5 | GPIO3_8 | CPU GPIO 3-8 |
| 6 | GPIO3_9 | CPU GPIO 3-9 |
| 7 | GPIO3_10 | CPU GPIO 3-10 |
| 8 | GPIO3_11 | CPU GPIO 3-11 |
| 9 | GPIO3_12 | CPU GPIO 3-12 |
| 10 | GPIO3_13 | CPU GPIO 3-13 |
| 11 | GPIO3_14 | CPU GPIO 3-14 |
| 12 | GPIO3_15 | CPU GPIO 3-15 |
| 13 | GND | Ground |
| 14 | ADC1_6 | CDU ADC1-6 |
| 15 | GND | Ground |
| 16 | ADC0_2 | CDU ADC0-2 |
| 17 | nc | not connected |
| 18 | ADC0_5 | CDU ADC0-5 |
| 19 | GND | Ground |
| 20 | ADC0_0 | CDU ADC0-0 |
| 21 | BAT+ | Battery + |
| 22 | VBAT | Not Used |
| Pin | Name | Description |
|---|---|---|
| 1 | VCC | 3.3V |
| 2 | GND | Ground |
| 3 | B2AUX16 | CPLD Bank2 AUX16 |
| 4 | B2AUX15 | CPLD Bank2 AUX15 |
| 5 | B2AUX14 | CPLD Bank2 AUX14 |
| 6 | B2AUX13 | CPLD Bank2 AUX13 |
| 7 | B2AUX12 | CPLD Bank2 AUX12 |
| 8 | B2AUX11 | CPLD Bank2 AUX11 |
| 9 | B2AUX10 | CPLD Bank2 AUX10 |
| 10 | B2AUX9 | CPLD Bank2 AUX9 |
| 11 | B2AUX8 | CPLD Bank2 AUX8 |
| 12 | B2AUX7 | CPLD Bank2 AUX7 |
| 13 | B2AUX6 | CPLD Bank2 AUX6 |
| 14 | B2AUX5 | CPLD Bank2 AUX5 |
| 15 | B2AUX4 | CPLD Bank2 AUX4 |
| 16 | B2AUX3 | CPLD Bank2 AUX3 |
| 17 | GCK2 | Clock Generator Out 2 |
| 18 | GCK1 | Clock Generator Out 1 |
| 19 | GCK0 | Clock Generator Out 0 |
| 20 | GND | Ground |
| Pin | Name | Description |
|---|---|---|
| 1 | CLKIN | not used |
| 2 | CLKOUT | not used |
| 3 | RESET | CPU Reset |
| 4 | GND | Ground |
| 5 | I2C1_SCL | I2C1 Serial Clock |
| 6 | I2C1_SDA | I2C1 Serial Data |
| 7 | SPIFL_MISO | SPI Flash Master in Slave Out (solder R218 for use) |
| 8 | SPIFL_SCK | SPI Flash Serial Clock (solder R217 for use) |
| 9 | SPIFL_MOSI | SPI Flash Slave In Slave Out (solder R219 for use) |
| 10 | GND | Ground |
| 11 | VCC | VCC 3.3 V |
| 12 | I2SO_RX_SCK | I2S RX Serial Clock |
| 13 | I2SO_RX_SDA | I2S RX Serial DATA Not used |
| 14 | I2SO_RX_MCLK | I2S RX M Clock |
| 15 | I2SO_RX_WS | I2S RX WS |
| 16 | I2SO_TX_SCK | I2S TX Serial Clock |
| 17 | I2SO_RX_MCLK | I2S TX M Clock |
| 18 | GND | Ground |
| 19 | U0_RXD | Uart 0 RX Data |
| 20 | U0_TXD | Uart 0 TX Data |
| 21 | P2_9 | Battery + |
| 22 | P2_13 | Not Used |
| 23 | P2_8 | Ground |
| 24 | I2C0_SDA | I2C 0 Serial Data |
| 25 | I2C0_SCL | I2C 0 Serial Clock |
| 26 | VDD | VDD RF 3.3 V Supply |
| Pin | Name | Description |
|---|---|---|
| 1 | GND | Ground |
| 2 | ISP | CPU ISP |
| 3 | n.c | Not Connected |
| 4 | U0_RXD | Uart 0 RX Data |
| 5 | U0_TXD | Uart 0 TX Data |
| 6 | RESET | CPU RESET |